20,00 mm-FRESA MICROGRANO DIN6528N 4Z RADIAL-CROMAX
20,00 mm-END MILL MICROGRAIN+CROMAX DIN6528N 4Z RADIAL-CROMAX
- 6528
- N
- Micrograin
- CROMAX
- 20.00
- 20.00
- 104
- 32.00
- 5
- 30º
- Flat
- 1
- Synthetic-Plastics
- Aluminium-Magnesium
- Cast Iron
- Stainless
- Steel
- Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Titanium Alloys
- Cast Iron (200-300 HB / 700-1000 N/mm2)
- Cast Iron (<200 HB / <700 N/mm2)
- Ferritic / Martensitic Stainless (<320 HB / <850 N/mm2)
- Austenitic Stainless (<250 HB / <850 N/mm2)
- Treated / Heat-Treatable Alloyed Steel (300-400 HB / 1000-1300 N/mm2)
- Alloyed Steel (<300 HB / <1000 N/mm2)
- Hard-Plastics
- Thermo-Plastics
- Alloys Al-Mg Si > 10% (<180 HB / <600 N/mm2)
- Alloys Al-Mg Si < 10% (<180 HB / <600 N/mm2)
- Al-Mg non-alloyed (<100 HB / <350 N/mm2)
- Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Construction / Carbon Steel (<250 HB / <850 N/mm2)
- 0.150
- 125-160
- 0.100
- 112-150
- 0.075
- 60-130
- 0.150
- 50-80
- 0.120
- 100-130
- 0.100
- 68-95
- 0.100
- 40-60
- 0.050
- 50-68
- 0.125
- 140-350
- 140-350
- 0.200
- 140-420
- 0.200
- 140-420
- 100-300
- 140-280
P.1 Construction / Carbon Steel (<250 HB/<850 N/mm2) Feed (mm/rev.) 0,150 Cutting Speed (m/min.) 125-160
P.2 Alloyed Steel (<300 HB / <1000 N/mm2) Feed (mm/rev.) 0,100 Cutting Speed (m/min.) 112-150
P.3 Treated/Heat-Treatable Alloyed Steel (300-400HB/1000-1300N/mm2) Feed (mm/rev.)0,075 Cutting Speed (m/min.) 60-130
M Austenitic Stainless (<250 HB / <850 N/mm2) Feed (mm/rev.) 0,150 Cutting Speed (m/min.) 50-80
P.5 Ferritic/Martensitic Stainless (320HB/<850 N/mm2) Feed (mm/rev.) 0,120 Cutting Speed (m/min.) 100-130
K.1 Cast Iron (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,100 Cutting Speed (m/min.) 68-95
K.2 Cast Iron (200-300 HB / 700-1000 N/mm2) Feed (mm/rev.) 0,100 Cutting Speed (m/min.) 40-60
S Heat-Resistant Alloys Feed (mm/0,050 Cutting Speed (m/min.) 50-68
N.1 Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,125 Cutting Speed (m/min.) 140-350
N.2 Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,125 Cutting Speed (m/min.) 140-350
N.3 Al-Mg non-alloyed (<100 HB / <350 N/mm2) Feed (mm/rev.) 0,200 Cutting Speed (m/min.) 140-420
N.4 Al-Mg Si < 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,200 Cutting Speed (m/min.) 140-420
N.5 Al-Mg Si > 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,200 Cutting Speed (m/min.) 100-300
N.6 Thermo-Plastics Feed (mm/rev.) 0,150 Cutting Speed (m/min.) 140-280
N.7 Hard-Plastics Feed (mm/rev.) 0,100 Cutting Speed (m/min.) 70-175