04,00 mm-FRESA MICROGRANO DIN6528N 2Z-CROMAX
04,00 mm-END MILL MICROGRAIN DIN6528N 2Z-CROMAX
- 6528
- N
- Micrograin
- CROMAX
- 4.00
- 4.00
- 50.00
- 8.00
- 2
- 30º
- Flat
- 1
- Synthetic-Plastics
- Aluminium-Magnesium
- Cast Iron
- Stainless
- Steel
- Cast Iron (<200 HB / <700 N/mm2)
- Ferritic / Martensitic Stainless (<320 HB / <850 N/mm2)
- Austenitic Stainless (<250 HB / <850 N/mm2)
- Treated / Heat-Treatable Alloyed Steel (300-400 HB / 1000-1300 N/mm2)
- Alloyed Steel (<300 HB / <1000 N/mm2)
- Hard-Plastics
- Thermo-Plastics
- Alloys Al-Mg Si > 10% (<180 HB / <600 N/mm2)
- Alloys Al-Mg Si < 10% (<180 HB / <600 N/mm2)
- Al-Mg non-alloyed (<100 HB / <350 N/mm2)
- Construction / Carbon Steel (<250 HB / <850 N/mm2)
- Cast Iron (200-300 HB / 700-1000 N/mm2)
- Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- 0.020
- 125-180
- 0.020
- 112-150
- 0.020
- 60-130
- 0.010
- 50-80
- 0.010
- 100-130
- 0.020
- 55-70
- 0.020
- 30-50
- 0.010
- 50-68
- 0.020
- 100-250
- 100-250
- 0.010
- 100-300
- 0.010
- 100-300
- 90-200
- 100-200
P.1 Construction / Carbon Steel (<250 HB/<850 N/mm2) Feed (mm/rev.) 0,020 Cutting Speed (m/min.) 125-180
P.2 Alloyed Steel (<300 HB / <1000 N/mm2) Feed (mm/rev.) 0,020 Cutting Speed (m/min.) 112-150
P.3 Treated/Heat-Treatable Alloyed Steel (300-400HB/1000-1300N/mm2) Feed (mm/rev.)0,020 Cutting Speed (m/min.) 60-130
M Austenitic Stainless (<250 HB / <850 N/mm2) Feed (mm/rev.) 0,010 Cutting Speed (m/min.) 50-80
P.5 Ferritic/Martensitic Stainless (320HB/<850 N/mm2) Feed (mm/rev.) 0,010 Cutting Speed (m/min.) 100-130
K.1 Cast Iron (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,020 Cutting Speed (m/min.) 55-70
K.2 Cast Iron (200-300 HB / 700-1000 N/mm2) Feed (mm/rev.) 0,020 Cutting Speed (m/min.) 30-50
S Heat-Resistant Alloys Feed (mm/0.010 Cutting Speed (m/min.) 50-68
N.1 Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,020 Cutting Speed (m/min.) 100-250
N.2 Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,020 Cutting Speed (m/min.) 100-250
N.3 Al-Mg non-alloyed (<100 HB / <350 N/mm2) Feed (mm/rev.) 0,010 Cutting Speed (m/min.) 100-300
N.4 Al-Mg Si < 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,010 Cutting Speed (m/min.) 100-300
N.5 Al-Mg Si > 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,010 Cutting Speed (m/min.) 90-200
N.6 Thermo-Plastics Feed (mm/rev.) 0,020 Cutting Speed (m/min.) 100-200
N.7 Hard-Plastics Feed (mm/rev.) 0,015 Cutting Speed (m/min.) 50-125