160X63X50 mm-FRESA AGUJERO DESBASTE HSSE DIN1880NR 2-CORTES-
050X36X22 mm-SHELL END MILL ROUGHING HSSE DIN1880NR
- 1880
- NR
- HSSE 5% Co
- 50.00
- 36.00
- 6
- 30º
- 2586
- 22.00
- 1
- Synthetic-Plastics
- Aluminium-Magnesium
- Copper-Bronze-Brass
- Thermo-Resistant Alloys
- Cast Iron
- Stainless
- Steel
- Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Titanium Alloys
- Cast Iron (200-300 HB / 700-1000 N/mm2)
- Cast Iron (<200 HB / <700 N/mm2)
- Ferritic / Martensitic Stainless (<320 HB / <850 N/mm2)
- Austenitic Stainless (<250 HB / <850 N/mm2)
- Alloyed Steel (<300 HB / <1000 N/mm2)
- Hard-Plastics
- Thermo-Plastics
- Alloys Al-Mg Si > 10% (<180 HB / <600 N/mm2)
- Alloys Al-Mg Si < 10% (<180 HB / <600 N/mm2)
- Al-Mg non-alloyed (<100 HB / <350 N/mm2)
- Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Construction / Carbon Steel (<250 HB / <850 N/mm2)
- 77754
P.1 Construction / Carbon Steel (<250 HB/<850 N/mm2) Feed (mm/rev.) 0,15 Cutting Speed (m/min.) 20-30
P.2 Alloyed Steel (<300 HB / <1000 N/mm2) Feed (mm/rev.) 0,12 Cutting Speed (m/min.) 15-30
P.3 Treated/Heat-Treatable Alloyed Steel (300-400HB/850-1300N/mm2) Feed (mm/rev.)0,08 Cutting Speed (m/min.) 12-16
M Austenitic Stainless (<250 HB / <850 N/mm2) Feed (mm/rev.) 0,10 Cutting Speed (m/min.) 15-20
P.5 Ferritic/Martensitic Stainless (320HB/<850 N/mm2) Feed (mm/rev.) 0,08 Cutting Speed (m/min.) 15-20
K.1 Cast Iron (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,22 Cutting Speed (m/min.) 12-18
K.2 Cast Iron (200-300 HB / 700-1000 N/mm2) Feed (mm/rev.) 0,18 Cutting Speed (m/min.) 12-18
S Titanium Alloys Feed (mm/rev.) 0,11 Cutting Speed (m/min.) 20-30
N.1 Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,15 Cutting Speed (m/min.) 25-32
N.2 Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,20 Cutting Speed (m/min.) 60-100
N.3 Al-Mg non-alloyed (<100 HB / <350 N/mm2) Feed (mm/rev.) 0,15 Cutting Speed (m/min.) 180-250
N.4 Al-Mg Si < 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,15 Cutting Speed (m/min.) 180-250
N.5 Al-Mg Si > 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,10 Cutting Speed (m/min.) 50-60
N.6 Thermo-Plastics Feed (mm/rev.) 0,12 Cutting Speed (m/min.) 100-150
N.7 Hard-Plastics Feed (mm/rev.) 0,12 Cutting Speed (m/min.) 100-150