ø160X10,00X40mm Z=28-FRESA AGUJERO HSSE DIN885B 3-CORTES DENTADO-RECTO-
080X14,00X27 mm-MILLING CUTTER HSSE DIN885B SIDE&FACE STRAIGHT TEETH
- 885
- B
- HSSE 5% Co
- 80.00
- 14.00
- 20
- 2587
- 27.00
- 1
- Synthetic-Plastics
- Aluminium-Magnesium
- Copper-Bronze-Brass
- Thermo-Resistant Alloys
- Cast Iron
- Stainless
- Steel
- Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Titanium Alloys
- Cast Iron (200-300 HB / 700-1000 N/mm2)
- Cast Iron (<200 HB / <700 N/mm2)
- Ferritic / Martensitic Stainless (<320 HB / <850 N/mm2)
- Austenitic Stainless (<250 HB / <850 N/mm2)
- Alloyed Steel (<300 HB / <1000 N/mm2)
- Hard-Plastics
- Thermo-Plastics
- Alloys Al-Mg Si > 10% (<180 HB / <600 N/mm2)
- Alloys Al-Mg Si < 10% (<180 HB / <600 N/mm2)
- Al-Mg non-alloyed (<100 HB / <350 N/mm2)
- Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Construction / Carbon Steel (<250 HB / <850 N/mm2)
- 52950
P.1 Construction / Carbon Steel (<250 HB/<850 N/mm2) Feed (mm/rev.) 0,06 Cutting Speed (m/min.) 20-30
P.2 Alloyed Steel (<300 HB / <1000 N/mm2) Feed (mm/rev.) 0,07 Cutting Speed (m/min.) 15-20
P.3 Treated/Heat-Treatable Alloyed Steel (300-400HB/850-1300N/mm2) Feed (mm/rev.)0,04 Cutting Speed (m/min.) 12-16
M Austenitic Stainless (<250 HB / <850 N/mm2) Feed (mm/rev.) 0,08 Cutting Speed (m/min.) 15-20
P.5 Ferritic/Martensitic Stainless (320HB/<850 N/mm2) Feed (mm/rev.) 0,04 Cutting Speed (m/min.) 15-20
K.1 Cast Iron (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,08 Cutting Speed (m/min.) 12-18
K.2 Cast Iron (200-300 HB / 700-1000 N/mm2) Feed (mm/rev.) 0,06 Cutting Speed (m/min.) 12-18
S Titanium Alloys Feed (mm/rev.) 0,07 Cutting Speed (m/min.) 20-30
N.1 Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,10 Cutting Speed (m/min.) 25-32
N.2 Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,10 Cutting Speed (m/min.) 60-100
N.3 Al-Mg non-alloyed (<100 HB / <350 N/mm2) Feed (mm/rev.) 0,07 Cutting Speed (m/min.) 180-250
N.4 Al-Mg Si < 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,07 Cutting Speed (m/min.) 180-250
N.5 Al-Mg Si > 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,07 Cutting Speed (m/min.) 50-60
N.6 Thermo-Plastics Feed (mm/rev.) 0,06 Cutting Speed (m/min.) 100-150
N.7 Hard-Plastics Feed (mm/rev.) 0,06 Cutting Speed (m/min.) 100-150