080X45X27 mm-FRESA AGUJERO DESBASTE PMX DIN1880NR 2-CORTES-TIALN-TOP
080X45X27 mm-SHELL END MILL ROUGHING PMX DIN1880NR-TIALN-TOP
- 1880
- NR
- PMX
- TIALN-TOP
- 80.00
- 45.00
- 10
- 30º
- 2586
- 27.00
- 1
- Aluminium-Magnesium
- Copper-Bronze-Brass
- Thermo-Resistant Alloys
- Cast Iron
- Stainless
- Steel
- Synthetic-Plastics
- Construction / Carbon Steel (<250 HB / <850 N/mm2)
- Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Al-Mg non-alloyed (<100 HB / <350 N/mm2)
- Alloys Al-Mg Si < 10% (<180 HB / <600 N/mm2)
- Alloys Al-Mg Si > 10% (<180 HB / <600 N/mm2)
- Thermo-Plastics
- Hard-Plastics
- Alloyed Steel (<300 HB / <1000 N/mm2)
- Austenitic Stainless (<250 HB / <850 N/mm2)
- Ferritic / Martensitic Stainless (<320 HB / <850 N/mm2)
- Cast Iron (<200 HB / <700 N/mm2)
- Cast Iron (200-300 HB / 700-1000 N/mm2)
- Titanium Alloys
- Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- 24-35
- 0.12
- 18-24
- 0.08
- 14-19
- 0.10
- 18-24
- 18-24
- 0.22
- 14-20
- 0.18
- 14-20
- 0.11
- 24-35
- 0.15
- 30-38
- 70-120
- 210-300
- 210-300
- 60-70
- 120-180
- 39030
P.1 Construction / Carbon Steel (<250 HB/<850 N/mm2) Feed (mm/rev.) 0,15 Cutting Speed (m/min.) 24-35
P.2 Alloyed Steel (<300 HB / <1000 N/mm2) Feed (mm/rev.) 0,12 Cutting Speed (m/min.) 18-24
P.3 Treated/Heat-Treatable Alloyed Steel (300-400HB/1000-1300N/mm2) Feed (mm/rev.)0,08 Cutting Speed (m/min.) 14-19
M Austenitic Stainless (<250 HB / <850 N/mm2) Feed (mm/rev.) 0,10 Cutting Speed (m/min.) 18-24
P.5 Ferritic/Martensitic Stainless (320HB/<850 N/mm2) Feed (mm/rev.) 0,08 Cutting Speed (m/min.) 18-24
K.1 Cast Iron (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,22 Cutting Speed (m/min.) 14-20
K.2 Cast Iron (200-300 HB / 700-1000 N/mm2) Feed (mm/rev.) 0,18 Cutting Speed (m/min.) 14-20
S Heat-Resistant Alloys Feed (mm/0,11 Cutting Speed (m/min.) 24-35
N.1 Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,15 Cutting Speed (m/min.) 30-38
N.2 Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,20 Cutting Speed (m/min.) 70-120
N.3 Al-Mg non-alloyed (<100 HB / <350 N/mm2) Feed (mm/rev.) 0,15 Cutting Speed (m/min.) 210-300
N.4 Al-Mg Si < 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,15 Cutting Speed (m/min.) 210-300
N.5 Al-Mg Si > 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,10 Cutting Speed (m/min.) 60-70
N.6 Thermo-Plastics Feed (mm/rev.) 0,12 Cutting Speed (m/min.) 120-180
N.7 Hard-Plastics Feed (mm/rev.) 0,12 Cutting Speed (m/min.) 120-180